Electrostatic Discharge(ESD) Analysis

What is ESD?
Electrostatic discharge(ESD) is the sudden and momentary electric current that flows between two objects at different electrical potentials caused by direct contact or induced by an electrostatic field.An Electrostatic Discharge (ESD) strike is a constant threat to device reliability and functionality. Many low-voltage core chips or system ASICs only offer device-level Human-Body Model (HBM) ESD device protection, which doesn’t address the risks of system-level ESD strikes.ESD can occur when an electronic device comes near the human body or when it’s around another device (machine interface contact). A prime example involves connecting together two devices, such as plugging a mobile phone into a laptop. The person’s hand may touch the connecting pins, or if the device is charged up, ESD may occur when mating the connectors.
ESD Damage
•Burn Out
•Breakdown of insulator
•Decrease of lifetime
•Software Failure
ESD Protection of an Smart Phone Circuit
Electrostatic discharge (ESD) looms as one of the biggest threats to a mobile phone’s sensitive components. ESD is a sudden high voltage spike caused by charged objects touching, or in close proximity to, each other. Since these voltage spikes typically produce thousands of volts, they may damage sensitive components (e.g., ICs) in the system
  • The IEC61000-4-2standard defines standard test conditions that electronic equipment should withstand. It assumes that the user will take no precautions to prevent any ESD damage, and it defines a variety of levels that the equipment should withstand.
  • The typical curve for an electrostatic discharge defined by IEC61000-4-2has a rise time of about 1 ns and a peak current level of around 30A.
ESD Analysis

Static charge is an unbalanced electrical charge at rest. Typically, it is created by insulator surfaces rubbing together or pulling apart. One surface gains electrons, while the other surface loses electrons. This results in an unbalanced electrical condition known as static charge. When a static charge moves from one surface to another, it becomes ESD. ESD is a miniature lightning bolt of charge that moves between two surfaces that have different potentials. It can occur only when the voltage differential between the two surfaces is sufficiently high to break down the dielectric strength of the medium separating the two surfaces. When a static charge moves, it becomes a current that damages or destroys gate oxide, metallization, and junctions. ESD can occur in any one of four different ways: a charged body can touch an IC, a charged IC can touch a grounded surface, a charged machine can touch an IC, or an electrostatic field can induce a voltage across a dielectric sufficient to break it down.

Comments

Post a Comment

Popular posts from this blog

Image
Slotted Waveguide Array Antenna Slotted antenna arrays used with waveguides are a popular antenna in navigation, radar, and other high-frequency systems. A waveguide is a very low loss transmission line. It allows propagating signals to a number of smaller antennas (slots). Each of these slots allows a little of the energy to radiate. Slot impedance and resonant behavior for a single slot are dependent on slot placement and size. Its exceptional directivity in the elevation plane gives it quite high power gain. The slotted waveguide has achieved most of its success when used in an omnidirectional role To make the unidirectional antenna radiate over the entire 360 degrees of azimuth, the second set of slots are cut on the back face of the waveguide. An 8×8 planar four pole X-band Tchebyshev dual inductive post substrate integrated waveguide filter from 10.15 GHz to 10.7 GHz is designed for terrestrial broadcasting. The filter is designed on the 5870 with a relative dielectric
Read more

Dual Channel Rotary Joint

Image
A Rotary Joint (RJ) is a wide spread microwave device that is used to change the direction of microwave propagation between two waveguides by rotating one with respect to another. Rotary joints find many applications in radar and satellite earth stations for functions such as polarization rotation; antenna feed systems and azimuth and elevation motions. Many styles of rotary joints are available for a variety of environmental conditions. Multichannel rotary joints must be carefully designed to achieve low channel loss and small rotational variations of this loss.   A n investigation was first carried out to review the state of the art in the field of multiple-channel rotary joints and to select the types of propagation modes that best satisfied the special system needs. A review of possible design approaches led to the selection of a concentric coaxial line configuration for the main body of the rotary joint, with integral transitions to waveguide at both ends for minimum over
Read more

QFN Package Simulation

Image
he Quad Flat No-lead (QFN) package is a CSP (plastic encapsulated package) with a copper lead frame substrate. QFN type package is one of the most cutting-edge IC packaging technologies in the electronics. The QFN is a leadless package where electrical contact to the PCB is made by soldering the leads on the bottom surface of the package to the PCB, instead of the conventional formed perimeter gull wing leads. The QFN-type package is known for its small size, cost-effectiveness and good production yields. QFN also possess certain mechanical advantages for high-speed circuits including improved co-planarity and heat dissipation. The QFN has pins on 4 edges of the bottom surface of the package. The QFN can have either a square or rectangle body as well as symmetric or asymmetric terminal patterns. The QFN was introduced to replace the gull wing lead Quad Flat Package (QFP) because the component leads are embedded in the plastic and cannot be bent during handling to insure consistent
Read more